How to Start a Motorcycle That Has Been Sitting

How to Start a Motorcycle That Has Been Sitting 1

If you’re like many motorcycle enthusiasts, you may only ride your bike during certain months out of the year. This can lead to your motorcycle sitting for long periods of time, which can be tough on the engine. Before you start your motorcycle after it has been sitting, there are a few things you should do to make sure everything goes smoothly.

First, check the oil level and add more if necessary. You should also check the tire pressure and inflate them if needed. It’s also a good idea to clean any dirt or debris that may have accumulated on the bike while it was sitting.

Once you’ve done all of this, you’re ready to start your motorcycle!

Old Motorcycle Won’t Start? Cheap Checks and Easy Fixes

  • If your motorcycle has been sitting for a while, there are a few things you need to do before starting it up
  • Check the oil level and add more if needed
  • This will help lubricate the engine and prevent damage
  • Clean out the carburetor and fuel tank
  • This will remove any dirt or debris that has built up over time and could clog the engine
  • Charge the battery or replace it if necessary
  • A dead battery will not start the motorcycle
  • Inspect all of the hoses and cables to make sure they are in good working order, as well as the tires for proper inflation levels
  • 5 Finally, check that there is enough gasoline in the tank before attempting to start it up
How to Start a Motorcycle That Has Been Sitting


Q: How Do I Start a Motorcycle That Has Been Sitting

If you’re like most motorcycle riders, you enjoy the occasional long ride. Maybe you even take a road trip or two each year. But what happens when you get home and your bike has been sitting in the garage for weeks or months?

Before you can hit the open road again, you need to start your motorcycle and get it running smoothly. Here’s how to do just that: 1. Check the oil level and add more if needed.

This is especially important if your bike has been sitting for a while since the oil can break down and degrade over time. You don’t want to damage your engine by riding with old, dirty oil. 2. Inspect the tires for any flat spots or cracks that may have developed from sitting in one spot for too long.

It’s also a good idea to check the air pressure and inflate them to the proper level before heading out on a ride. 3. Start by giving the throttle a few quick blips before fully engaging it so that the engine doesn’t rev up too high right away. Then let out the clutch slowly as you give gas at about 1/8 throttle until it catches and starts running on its own.

4. Continue to give it gas as needed to keep it running, but avoid revving too high at first since this could cause damage after such a long period of inactivity. Let it warm up gradually so that all of the moving parts have a chance to loosen up properly before putting them under duress.

First, Check the Oil Level And Make Sure It’S Full

If the oil level is low, add more oil until it reaches the full mark. Next, locate the air filter and check to see if it’s dirty. If it is, replace it with a new one.

Then, find the spark plugs and make sure they’re not corroded or damaged. If they are, replace them with new ones. Finally, check all of the fluids (coolant, power steering fluid, etc.) and top them off if necessary.

Next, Check the Gas Tank And Add Fresh Gas If Needed

Before starting your car, it’s important to make sure that you have enough gas. Checking the gas tank is a simple process that only takes a few seconds. Here’s how to do it:

Locate the gas gauge on your dashboard. This is usually located on the right side of the dash, near the speedometer. Start the car and let it run for a minute or two so that the gauge can give an accurate reading.

Observe the needle on the gas gauge. If it’s close to empty (the “E” mark), then you’ll need to add some gasoline. Adding gasoline is easy – just find a nearby gas station and fill up your tank!

Finally, Clean the Spark Plugs And Make Sure They are in Good Condition

How to Clean Your Spark Plugs It’s important to keep your spark plugs clean so that your engine will run smoothly. Here’s how to clean them:

1. Remove the spark plugs from the engine. You’ll need a spark plug wrench to do this. 2. Inspect the spark plugs.

If they’re dirty, you’ll need to clean them. 3. To clean the spark plugs, you can use a wire brush or a commercial cleaner designed for this purpose. Be sure to follow the instructions on the cleaner carefully.

Once You’Ve Done All of This, Try Starting the Motorcycle As You Normally Would

Assuming you have a kick start motorcycle, the below steps are how you would go about starting it: 1. Make sure the bike is in neutral by checking that the little indicator on the dash is lined up with the line in the center. If it’s not, press down on the shifter until it clicks into place.

2. Push down on the clutch lever (this is usually located on the left handlebar) and hold it there while you kickstart the engine. The specific way to do this varies depending on whether you have a two-stroke or four-stroke engine, so consult your owner’s manual if you’re unsure. 3. Once the engine has started, let go of the clutch lever and give it some gas by twisting the throttle (usually located on the right handlebar).

You may need to keep your foot on the clutch pedal for a few seconds as the bike warms up and stabilizes itself.


If you’re lucky enough to have a motorcycle that’s been sitting in storage, there are a few things you need to do before you can start it up again. First, check the oil level and quality. If it’s low or dirty, change it.

Next, check the gas tank. If it’s empty, fill it up with fresh gas. Finally, check the battery.

If it’s dead, replace it with a new one. Once you’ve done all of this, your motorcycle should be ready to start up and ride!

Please follow and like us:
How to Start a Motorcycle That Has Been Sitting 4
Pin Share

Leave a Reply

Your email address will not be published.